maximum ra tings and electrical characteristics ratings at 25 o c ambient temperature unless otherwise specified. resistive or inductive load. 2RS101M thru 2rs107m m a x i m u m r a t ings (@ t a =25 o c unless otherwise noted) electrical characteristics (@t a =25 o c unless otherwise noted) dimensions in inches and (millimeters) fea tures * low leakage * low forward voltage * low cost * mounting position: any mechanical da t a * epoxy: device has ul flammability classification 94v-o rs-1m r a tings maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current at t a = 105 o c peak forward surge current 8.3 ms single half sine-wave superimposed on rated load (jedec method) typical thermal resistance (note 1) typical current squarad time symbol v rrm v dc i fsm i 2 t t j , t stg v rms units volts volts amps 2.0 60 14.9 15 50 amps a 2 /sec 0 c/ w 0 c operating a nd storage t e mperature ra n g e r q jc r q ja i o -55 to + 150 volts 100 2RS101M 2rs103m 2rs105m 2rs102m 2rs104m 200 800 2rs106m 50 100 200 800 50 70 140 560 35 1000 2rs107m 1000 700 400 400 280 600 600 420 2010-05 rev:b characteristics at rated dc blocking voltage v f symbol i r mamps maximum dc reverse current maximum instantaneous forward voltage at 2.0a dc volts 5.0 @t a = 100 o c @t a = 25 o c 1.1 100 units 2RS101M 2rs103m 2rs105m 2rs102m 2rs104m 2rs106m 2rs107m notes : 1. thermal resistance : heat-sink case mounted or if pcb mounted. 2. "fully rohs compliant", "100% sn plating (pb-free)". .582 (14.8) .559 (14.2) .421 (10.7) .406 (10.3) .582 (14.8) .543 (13.8) .059 (1.5) .043 (1.1) .059 (1.5) .043 (1.1) .09 (2.3) .146 (3.7) .130 (3.3) .024 (0.6) .016 (0.4) .043 (0.9) .035 (0.6) .165 (4.2) .149 (3.8) .165 (4.2) .149 (3.8) .165 (4.2) .149 (3.8) 3. available in halogen-free epoxy by adding suffix -hf after the part nbr. single-phase glass passivated silicon bridge rectifier voltage range 50 to 1000 volts current 2.0 amperes
instantaneous forward voltage, (v) percent rated peak reverse voltage, (%) instantaneous forward current, (a) ambient temperature, ( o c) 0 0.1 0.4 0.01 0.04 1.0 4 average forward current, (a) 0 0.4 0.8 1.2 2.0 1.6 2.0 1.5 0.5 1.0 3.0 2.5 3.5 150 100 50 0 0 20 1.0 0.1 10 100 1000 120 100 40 60 80 140 rating and characteristics curves ( 2RS101M thru 2rs107m ) fig.3 typical reverse characteristics fig.1 typical forward current derating curve fig.2 typical instantaneous forward characteristics instantaneous reverse current, (ma) number of cycles at 60hz peak forward surge current, (a) 1 0 60 80 100 20 40 120 5 2 10 20 50 100 fig.4 maximum non-repetitive forward surge current single phase half wave 60 hz inductive or resistive load t a = 100 o c t a = 25 o c 8.3ms single half sine-wave jedec method t a = 25 o c pulse width = 300ms 1% duty cycle
marking description 2 r s 1 0 x m v y ww rectron logo part no. year ? code: (y:last digit of year& a:2010, b:2011??) week ? code: (ww:01~52) voltage-code 1-------50v 5-------600v 2-------100v 6-------800v 3-------200v 7-------1000v 4-------400v ul logo
packaging of diode and bridge rectifiers tube pack package ea per box inner box size (mm) carton size (mm) ea per carton weight(kg) rs-1m 1,350 540*118*118 560*259*144 2,700 12.03 packing code -c
rectron inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. rectron inc or anyone on its behalf assumes no responsibility or liabi- lity for any errors or inaccuracies. data sheet specifications and its information contained are intended to provide a product description only. "typical" paramet- ers which may be included on rectron data sheets and/ or specifications ca- n and do vary in different applications and actual performance may vary over ti- me. rectron inc does not assume any liability arising out of the application or use of any product or circuit. rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other rela- ted applications where a failure or malfunction of component or circuitry may di- rectly or indirectly cause injury or threaten a life without expressed written appr- oval of rectron inc. customers using or selling rectron components for use in such applications do so at their own risk and shall agree to fully indemnify rect- ron inc and its subsidiaries harmless against all claims, damages and expendit- ures. disclaimer notice
|
